Video scenes shots:
Watch the video:
Other videos by this author:
 |
Pizza Oven Speed Control Repair Pt2 - It Shows Signs of Life Posted by: Aussie50
Video duration: 529 seconds I don't think its as dead as some people thought :D, just needs replacement MOV's and to be refitted to the rest of the system for testing |
 |
Can it Be Fixed - 240V Vs 120V Speed Control Repair Help needed Posted by: Aussie50
Video duration: 184 seconds Sombody kinda fucked up and put 240V into a 120V Pizza oven and smoke came out of the speed controller :( its an expensive item so they sent it to me to repair or at least get a good idea on how fucked it is. I doubt its fixable but I am interested to know what the MOV-like parts are and if they are the only part that's gone. |
 |
Ramblotronic Monday - Cars and more Cars Posted by: Aussie50
Video duration: 479 seconds Ford should be nicer to drive with the front end all rebuilt!, likewise I have replaced the rear brakes and will be getting a new windscreen fitted next week. For the dead Odometer I got a pair of replacement gears on order from Ebay to repair it. nice and simple for $26. Nissan K11 Micra arrives at the end of the week too :D fun little thing that is! |
 |
Miele Flamespin 3000 Perfect Full Speed Run 3.0 Posted by: Aussie50
Video duration: 240 seconds perfect until the already damaged drive belt tore apart and it came to a rattly stop :D "I Want Flames" - Photonicinduction ( http://www.youtube.c om/photonvids ) |
 |
Miele Flamespin 3000 Test Run 2.0 Posted by: Aussie50
Video duration: 389 seconds I have fixed the mechanical noise. the back panel warped and was rubbing on the inner drum. Test Run 3.0 should be much better! the loud bangs were the heating elements blowing out their end plugs. note to self, remove heating elements before exposing to fire :D |
 |
Dell Lattitude D510 Laptop Autopsy Posted by: Aussie50
Video duration: 1117 seconds This one got a lot of water damage but was still fun to strip down!, lots of interesting bits and magnesium chassis parts! |
 |
Old Swan Compressor Runs Again Posted by: Aussie50
Video duration: 134 seconds After much internet problems today I can finally upload again. Compressor should really have a 2800rpm motor on it, but it works well with the 1440rpm one. |
 |
Ramblotronic Thursday - Cars Politics and other Good Stuff Posted by: Aussie50
Video duration: 488 seconds Wow i'm going to be busy with this car, having only 7 days before the RWC inspection expires sucks Ball Joints on the Ford apparently require a press, this is going to be fun :( |
 |
Hitachi Ignition Coil On Plug Module Test Posted by: Aussie50
Video duration: 274 seconds Thanks to Phil @ Latrobe Uni ( http://www.youtube.c om/haxby2008 ) for figuring out how to fire one of these coils off. they put out roughly 60Kv, with a lot of grunt :D I would not want to get shocked by one :D, could be worse than a commercial tazer!. |
 |
Saturday Fun - Viewer Visits, LPG Pump and Ford Fairmont Work Posted by: Aussie50
Video duration: 609 seconds I accidentally deleted the short clip that I did when Mattyvt93 and Starfleet0 were here but it wasn't much anyway http://www.youtub e.com/user/Starfleet 0 http://www.youtub e.com/mattyvt93 either way I am slowly working through various projects. and will have a test and run video on the LPG pump online soon |
 |
Miele Flamespin 3000 Oil Pump Build Posted by: Aussie50
Video duration: 470 seconds this thing will be off its tits once I get the fuel oil delivery right :D |
 |
Running a Light Load on Bosch 115A Alternator Posted by: Aussie50
Video duration: 179 seconds for those who wanted to see some load testing, I need way more motor HP before I can really load it up |
 |
Testing a Bosch Alternator with a 3 Phase Motor Posted by: Aussie50
Video duration: 458 seconds Battery, + Excitation charge + Rotational force = Alternating Current!, put that through a Rectifier and you have Direct Current! |
 |
Dangers of Dismantling a Magnetron Posted by: Aussie50
Video duration: 161 seconds A few people asked me about the 'dangerous material' in a magnetron, and its in the most harmless looking part. the insulator. Beryllium Oxide ceramics are nasty stuff when broken up. http://en.wikipedia. org/wiki/Beryllium_o xide |
 |
Ramblotronic Stormy Wednesday - Motor and Alternator test Rig Posted by: Aussie50
Video duration: 690 seconds weather got a bit crazy but I did get the alternator rig finished for testing |
 |
Need help ID Haldex Barnes 8101 Hydraulic Pump Posted by: Aussie50
Video duration: 140 seconds I've been asked to get some info on this pump for a Ebay auction, however I have not found a official listing for it :( I know its for a Hydro-static lawn mower, but that about all :(. could it be a custom pump? |
 |
Random Mercedes Benz Vito Alternator -Bosch 115A Posted by: Aussie50
Video duration: 283 seconds I have no idea why I have this new alternator, the clutch seem to work fine and it excites when I connect 12V to the excitation terminal via a 5W lamp. guess I should run it under power and see what happens :D, see how many lead acid batteries I can charge before I stall the diesel engine or smoke the alternator :D |
 |
Ramblotronic Monday - Slowly Sorting Packages out Posted by: Aussie50
Video duration: 334 seconds Now YT is spazzing out and trying to re-upload my Miele Flamespin 3000 video every time I select the 48V Telecom PSU Vid!!!. I will try again tomorrow. |
 |
Miele Flamespin 3000 Waste Oil Burner Pt1 Posted by: Aussie50
Video duration: 823 seconds Almost finished, just needs a good oil delivery bar and possibly a propane pre-heater torch, not hard to do tho built from a scrap miele front load washing machine drum unit and some scrap steel |
 |
Fun With Microwave - Light Bulbs - Bottles Etc Posted by: Aussie50
Video duration: 773 seconds Microwave Radiation FTW :D |
 |
Chrysler Voyager Dash Cluster Autopsy Posted by: Aussie50
Video duration: 847 seconds modern crap, not much to learn from these without a schematic :( |
 |
Miele Washing Machine Gets Stress Tested Posted by: Aussie50
Video duration: 456 seconds I think I broke it. I will be saving the drum unit and motor for a more fiery experiment :D, the rest can be incinerated and loaded up as scrap steel. |
 |
Yanmar YSE12G Cold Crank Start Fail Posted by: Aussie50
Video duration: 308 seconds She's just being a little bit stubborn, and no, the 3T72HA starter did not fit :( its easily started with 2 people, 1 to crank like mad, 1 to operate the decomp lever |
 |
Ramblotronic Thursday - Shipping, Testing and Building Stuff Posted by: Aussie50
Video duration: 474 seconds Ed Rambles, You Listen, and the world keeps turning. |
