Watching: More beater car maintenance

Video scenes shots:

Watch the video:

Other videos by this author:

	My Trangmission. My New One. Posted by: mx3sleeper Video duration: 658 seconds I FINALLY got my Trangmission!!! It's a 87-88 turbo one not the 89-91 turbo tranny I was looking for. it's not as beefy as the 89-91 but hopefully it last the summer!. In This video I swap out the trans, show the damage to the old one and take the car for a little test cruise.

	How to Rebuild and Port a Rotary Engine : Part 7 Posted by: mx3sleeper Video duration: 543 seconds Please Vote for my Video Entry in Mazda Canada's Defy Convention Contest!!! http://on.fb.me/HEoo S1 only one vote counts In this video I finish off the ports on the center iron, and put my turbo's all back together.

	RX7 FC3s In Car Drifts Posted by: mx3sleeper Video duration: 16 seconds

	How to Rebuild and Port a Rotary Engine : Part 6 Posted by: mx3sleeper Video duration: 1395 seconds In This video I show how to Port the Primary intake port start to finish. If you haven't voted for my video please vote! http://on.fb.me/HEoo S1

	How To Rebuild an Port a Rotary Engine : Part 5 Posted by: mx3sleeper Video duration: 669 seconds Please vote for my video http://on.fb.me/HEoo S1 In this video I get my turbo's cleaned up and ready to put back together, and I start porting the center iron.

	Mazda Contest - Defy Convention PLEASE VOTE! Posted by: mx3sleeper Video duration: 162 seconds Please Vote!!! http://on.fb.me/HEoo S1 This is my Entry for Mazda's Defy Convention contest. Help me out and vote please! Special thanks to www.youtube.com/arca nefireandicemusic for the music

	How to Rebuild and Port a Rotary Engine : Part 4 Posted by: mx3sleeper Video duration: 908 seconds in this video I start cleaning the engine parts, and working on the turbo's a bit.

	How to Rebuild and Port a Rotary Engine: Part 3 Posted by: mx3sleeper Video duration: 1078 seconds How to Rebuild and Port a Rotary Engine: Part 3 In this video I disassemble the engine I had to trick Pug1 and Bam and tell them I was having a hamburger picnic to get them to come help. check out their channels www.youtube.com/1 puglife www.youtube.com/b reedinantlermike

	How to Rebuild and Port a Rotary Engine : Part 2 Posted by: mx3sleeper Video duration: 588 seconds How to Rebuild and Port a Rotary Engine : Part 2 In this video I strip the engine down to the bare keg getting it ready to tear it apart.

	How to Rebuild and Port a Rotary Engine : Part 1 Posted by: mx3sleeper Video duration: 982 seconds How to Rebuild and Port a Rotary Engine : Part 1 In this Part I Remove the engine from the car

02 Mini Cooper getting pulled outta the ditch
Posted by: mx3sleeper

Video duration: 285 seconds

This guy came up from Pennsylvania , He tried an ebrake slide in a gravel parking lot and flipped his car in the ditch. we got it out and bent his shit straight so he could atleast limp it home.
check out his channel http://www.youtube.c om/rbuffum
For the video's of the crash http://www.youtube.c om/1puglife

A Romp in the Red Rocket
Posted by: mx3sleeper

Video duration: 681 seconds

So its Rainy out today , I made this video last week but the audio in the car is all dicked figured I'd just toss this up. I think the tape on the camera was vibrating or something. the solid engine mounts rattle everything lol. Let me know if you guys like this or if its just boring , I'll have some better ones as it gets nicer.

	Mazda RX-7 new Exhaust Sound, And Junkyard Run Posted by: mx3sleeper Video duration: 538 seconds I started this video on monday finally finished it off and I forgot to make an ending ffs!. anyways I fixed the leaks in my exhaust did an oil change got some good exhaust clips, then went to the junkyard to get a throttle cable for my friends car and I tossed it on for him.

	Midpipe Install on Mazda RX-7 FD3S Posted by: mx3sleeper Video duration: 260 seconds I put my midpipe on the FD today. fired it Up but it Leaks around the Downpipe I was afraid to snap the studs off so I probably could have put them on tighter. So I'll have to fix it up tomorrow

	Mazda RX-7 Turbo Solenoid Replacement Posted by: mx3sleeper Video duration: 291 seconds I only had enough time to swap out the turbo control and pre scroll / wg solenoids and got the engine bay all back together. tomorrow I just have to toss the finish off the midpipe and I can fire it up finally :)

$3\" Downpipe and midpipe install on Mazda RX-7 FD3S$	3" Downpipe and midpipe install on Mazda RX-7 FD3S Posted by: mx3sleeper Video duration: 319 seconds I swapped out the stock downpipe and made a 3" midpipe with 3" highflow cat and 3" glass pack. It's pretty much all done I just have to finish up tomorrow.

	Installing Differential in my RX7 FD3S Posted by: mx3sleeper Video duration: 290 seconds I made sort of a short video putting my differential in the parts car. I show all the parts I got to work on my exhaust to make it a full 3" downpipe and midpipe.

	CV Boot Strap Replacement Posted by: mx3sleeper Video duration: 512 seconds I didn't get the Diff in today , was dicking around trying to figure those straps out.I should get the diff in tomorrow and spray the bottom of the trunk with rocker guard.

	Seafoam in the Ford Focus Posted by: mx3sleeper Video duration: 409 seconds I haven't made a video in a bit so I went out and seafoamed my beater car, worked friggen great! then I went and fired up the black rx7. gonna try to make a video each day this week so check back

	$20 Junkyard Fix Posted by: mx3sleeper Video duration: 522 seconds $20 Junkyard Fix on my Focus beater car. My vents wouldn't switch anymore so I got a cable from the junkyard and picked up a sensor to get rid of my check engine light while I was at it. all for $20 even

$I Dicked\$	I Dicked'er BIGTIME! Posted by: mx3sleeper Video duration: 225 seconds So the doctor frigged us over made us have our baby early. So I sonofabitch recorded my g/f and made a little video.

Car Maintenance Videos

Car Maintenance Related Videos

Car Maintenance Sponsors